View UM232R_4366971.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TM
Future Technology Devices International Ltd.
UM232R USB- Serial UART Development Module
Incorporating Clock Generator Output and FTDIChip-IDTM Security Dongle
The UM232R is a development module which uses FTDI's FT232RL, the latest device to be added to FTDI's range of USB UART interface Integrated Circuit Devices. The FT232RL is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-IDTM security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are available. USB to serial interface designs using the FT232RL have been further simplified by fully integrating the external EEPROM, clock circuit and USB resistors onto the device. The FT232RL adds two new functions compared with its predecessors, effectively making it a "3-in-1" chip for some application areas. The internally generated clock (6MHz, 12MHz, 24MHz, and 48MHz) can be brought out of the device and used to drive a microcontroller or external logic. A unique number (the FTDIChip-IDTM) is burnt into the device during manufacture and is readable over USB, thus forming the basis of a security dongle which can be used to protect customer application software from being copied. The UM232R is supplied on a PCB which is designed to plug into a standard 15.0mm (0.6" ) wide 24 pin DIP socket. All components used, including the FT232RL are Pb-free (RoHS compliant).
Copyright (c) Future Technology Devices International Ltd. 2005
1. Features
1.1 Hardware Features
* * * * * * * * * * * * * * * * * * Single chip USB to asynchronous serial data transfer interface. Entire USB protocol handled on the chip - No USB-specific firmware programming required. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity. Fully assisted hardware or X-On / X-Off software handshaking. Data transfer rates from 300 baud to 3 Megabaud (RS422 / RS485 and at TTL levels) and 300 baud to 1 Megabaud (RS232). FTDI's royalty-free VCP and D2XX drivers eliminate the requirement for USB driver development in most cases. In-built support for event characters and line break condition. New USB FTDIChip-IDTM feature. New configurable CBUS I/O pins. Auto transmit buffer control for RS485 applications. Transmit and receive LED drive signals. New 48MHz, 24MHz,12MHz, and 6MHz clock output signal Options for driving external MCU or FPGA. FIFO receive and transmit buffers for high data throughput. Adjustable receive buffer timeout. Synchronous and asynchronous bit bang mode interface options with RD# and WR# strobes. New CBUS bit bang mode option. Integrated 1024 bit internal EEPROM for storing USB VID, PID, serial number and product description strings, and CBUS I/O configuration. Device supplied preprogrammed with unique USB serial number. * * * * * * * * * * * * * * * * * * * * * *
Page 2
Support for USB suspend and resume. Support for bus powered, self powered, and highpower bus powered USB configurations. On board jumper allows for selection of USB bus powered supply or self powered supply. Integrated 3.3V level converter for USB I/O. Integrated level converter on UART and CBUS for interfacing to 5V - 1.8V Logic. On board jumper allows for selection of UART and CBUS interface IO voltage. True 5V / 3.3V / 2.8V / 1.8V CMOS drive output and TTL input. High I/O pin output drive option. Integrated USB resistors. Integrated power-on-reset circuit. Fully integrated clock - no external crystal, oscillator, or resonator required. Fully integrated AVCC supply filtering - No separate AVCC pin and no external R-C filter required. UART signal inversion option. USB bulk transfer mode. 3.3V to 5.25V Single Supply Operation. Low operating and USB suspend current. Low USB bandwidth consumption. UHCI / OHCI / EHCI host controller compatible USB 2.0 Full Speed compatible. -40C to 85C extended operating temperature range. Supplied in PCB designed to fit a standard 15.0mm (0.6") wide 24 pin DIP socket. Pins are on a 2.60mm (0.1") pitch. On board USB `B' socket allows module to be connected to a PC via a standard A to B USB cable.
Royalty-Free VIRTUAL COM PORT (VCP) DRIVERS for... * Windows 98, 98SE, ME, 2000, Server 2003, XP. * Windows Vista / Longhorn* * Windows XP 64-bit.* * Windows XP Embedded. * Windows CE.NET 4.2 & 5.0 * MAC OS 8 / 9, OS-X * Linux 2.4 and greater
1.2 Driver Support
Royalty-Free D2XX Direct Drivers (USB Drivers + DLL S/W Interface) * Windows 98, 98SE, ME, 2000, Server 2003, XP. * Windows Vista / Longhorn* * Windows XP 64-bit.* * Windows XP Embedded. * Windows CE.NET 4.2 & 5.0 * Linux 2.4 and greater
The drivers listed above are all available to download for free from the FTDI website. Various 3rd Party Drivers are also available for various other operating systems - see the FTDI website for details.
* Currently Under Development. Contact FTDI for availability.
* * * * * * * *
USB to RS232 / RS422 / RS485 Converters Upgrading Legacy Peripherals to USB Cellular and Cordless Phone USB data transfer cables and interfaces Interfacing MCU / PLD / FPGA based designs to USB USB Audio and Low Bandwidth Video data transfer PDA to USB data transfer USB Smart Card Readers USB Instrumentation
1.3 Typical Applications
* * * * * * * * *
USB Industrial Control USB MP3 Player Interface USB FLASH Card Reader / Writers Set Top Box PC - USB interface USB Digital Camera Interface USB Hardware Modems USB Wireless Modems USB Bar Code Readers USB Software / Hardware Encryption Dongles
(c) Future Technology Devices International Ltd. 2005
UM232R USB-Serial UART Development Module Datasheet Version 1.02
2. FT232RL Features and Enhancements
2.1 Key Features
Page 3
This section summarises the key features and enhancements of the FT232RL IC device which is used on the UM232R Module. For further details, consult the FT232R datasheet, which is available from the FTDI website. Integrated Clock Circuit - Previous generations of FTDI's USB UART devices required an external crystal or ceramic resonator. The clock circuit has now been integrated onto the device meaning that no crystal or ceramic resonator is required. However, if required, an external 12MHz crystal can be used as the clock source. Integrated EEPROM - Previous generations of FTDI's USB UART devices required an external EEPROM if the device were to use USB Vendor ID (VID), Product ID (PID), serial number and product description strings other than the default values in the device itself. This external EEPROM has now been integrated onto the FT232R chip meaning that all designs have the option to change the product description strings. A user area of the internal EEPROM is available for storing additional data. The internal EEPROM is programmable in circuit, over USB without any additional voltage requirement. Preprogrammed EEPROM - The FT232R is supplied with its internal EEPROM preprogrammed with a serial number which is unique to each individual device. This, in most cases, will remove the need to program the device EEPROM. Integrated USB Resistors - Previous generations of FTDI's USB UART devices required two external series resistors on the USBDP and USBDM lines, and a 1.5 k pull up resistor on USBDP. These three resistors have now been integrated onto the device. Integrated AVCC Filtering - Previous generations of FTDI's USB UART devices had a separate AVCC pin - the supply to the internal PLL. This pin required an external R-C filter. The separate AVCC pin is now connected internally to VCC, and the filter has now been integrated onto the chip. Less External Components - Integration of the crystal, EEPROM, USB resistors, and AVCC filter will substantially reduce the bill of materials cost for USB interface designs using the FT232R compared to its FT232BM predecessor. Configurable CBUS I/O Pin Options - There are now 5 configurable Control Bus (CBUS) lines. Options are TXDEN - transmit enable for RS485 designs, PWREN# - Power control for high power, bus powered designs, TXLED# - for pulsing an LED upon transmission of data, RXLED# - for pulsing an LED upon receiving data, TX&RXLED# - which will pulse an LED upon transmission OR reception of data, SLEEP# - indicates that the device going into USB suspend mode, CLK48 / CLK24 / CLK12 / CLK6 - 48MHz, 24MHz,12MHz, and 6MHz clock output signal options. There is also the option to bring out bit bang mode read and write strobes (see below). The CBUS lines can be configured with any one of these output options by setting bits in the internal EEPROM. The device is supplied with the most commonly used pin definitions preprogrammed - see Section 8 for details. Enhanced Asynchronous Bit Bang Mode with RD# and WR# Strobes - The FT232R supports FTDI's BM chip bit bang mode. In bit bang mode, the eight UART lines can be switched from the regular interface mode to an 8-bit general purpose I/O port. Data packets can be sent to the device and they will be sequentially sent to the interface at a rate controlled by an internal timer (equivalent to the baud rate prescaler). With the FT232R device this mode has been enhanced so that the internal RD# and WR# strobes are now brought out of the device which can be used to allow external logic to be clocked by accesses to the bit bang I/O bus. This option will be described more fully in a separate application note. Synchronous Bit Bang Mode - Synchronous bit bang mode differs from asynchronous bit bang mode in that the interface pins are only read when the device is written to. Thus making it easier for the controlling program to measure the response to an output stimulus as the data returned is synchronous to the output data. The feature was previously seen in FTDI's FT2232C device. This option will be described more fully in a separate application note. CBUS Bit Bang Mode - This mode allows four of the CBUS pins to be individually configured as GPIO pins, similar to Asynchronous bit bang mode. It is possible to use this mode while the UART interface is being used, thus providing up to four general purpose I/O pins which are available during normal operation. An application note describing this feature is available separately from the FTDI website.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
Page 4
Lower Supply Voltage - Previous generations of the chip required 5V supply on the VCC pin. The FT232R will work with a Vcc supply in the range 3.3V - 5.25V. Bus powered designs would still take their supply from the 5V on the USB bus, but for self powered designs where only 3.3V is available and there is no 5V supply there is no longer any need for an additional external regulator. Integrated Level Converter on UART Interface and Control Signals - VCCIO pin supply can be from 1.8V to 5V. Connecting the VCCIO pin to 1.8V, 2.8V, or 3.3V allows the device to directly interface to 1.8V, 2.8V or 3.3V and other logic families without the need for external level converter I.C. devices. 5V / 3.3V / 2.8V / 1.8V Logic Interface - The FT232R provides true CMOS Drive Outputs and TTL level Inputs. Integrated Power-On-Reset (POR) Circuit- The device incorporates an internal POR function. A RESET# pin is available in order to allow external logic to reset the FT232R where required. However, for many applications the RESET# pin can be left unconnected, or pulled up to VCCIO. Lower Operating and Suspend Current - The device operating supply current has been further reduced to 15mA, and the suspend current has been reduced to around 70A. This allows greater margin for peripheral designs to meet the USB suspend current limit of 500A. Low USB Bandwidth Consumption - The operation of the USB interface to the FT232R has been designed to use as little as possible of the total USB bandwidth available from the USB host controller. High Output Drive Option - The UART interface and CBUS I/O pins can be made to drive out at three times the standard signal drive level thus allowing multiple devices to be driven, or devices that require a greater signal drive strength to be interfaced to the FT232R. This option is enabled in the internal EEPROM. Power Management Control for USB Bus Powered, High Current Designs- The PWREN# signal can be used to directly drive a transistor or P-Channel MOSFET in applications where power switching of external circuitry is required. An option in the internal EEPROM makes the device gently pull down on its UART interface lines when the power is shut off (PWREN# is high). In this mode any residual voltage on external circuitry is bled to GND when power is removed, thus ensuring that external circuitry controlled by PWREN# resets reliably when power is restored. UART Pin Signal Inversion - The sense of each of the eight UART signals can be individually inverted by setting options in the internal EEPROM. Thus, CTS# (active low) can be changed to CTS (active high), or TXD can be changed to TXD#. FTDIChip-IDTM - Each FT232R is assigned a unique number which is burnt into the device at manufacture. This ID number cannot be reprogrammed by product manufacturers or end-users. This allows the possibility of using FT232R based dongles for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-IDTM number when encrypted with other information. This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-IDTM to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note describing this feature is available separately from the FTDI website. Improved EMI Performance - The reduced operating current and improved on-chip VCC decoupling significantly improves the ease of PCB design requirements in order to meet FCC, CE and other EMI related specifications. Programmable Receive Buffer Timeout - The receive buffer timeout is used to flush remaining data from the receive buffer. This time defaults to 16ms, but is programmable over USB in 1ms increments from 1ms to 255ms, thus allowing the device to be optimised for protocols that require fast response times from short data packets. Baud Rates - The FT232R supports all standard baud rates and non-standard baud rates from 300 Baud up to 3 Megabaud. Achievable non-standard baud rates are calculated as follows Baud Rate = 3000000 / (n + x) where n can be any integer between 2 and 16,384 ( = 214 ) and x can be a sub-integer of the value 0, 0.125, 0.25, 0.375, 0.5, 0.625, 0.75, or 0.875. When n = 1, x = 0, i.e. baud rate divisors with values between 1 and 2 are not possible. This gives achievable baud rates in the range 183.1 baud to 3,000,000 baud. When a non-standard baud rate is required simply pass the required baud rate value to the driver as normal, and the FTDI driver will calculate the required divisor, and set the baud rate. See FTDI application note AN232B-05 for more details.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
Page 5
Extended Operating Temperature Range - The FT232R operates over an extended temperature range of -40 to +85 C thus allowing the device to be used in automotive and industrial applications. New Package Options - The FT232R is available in two packages - a compact 28 pin SSOP ( FT232RL) and an ultra-compact 5mm x 5mm pinless QFN-32 package ( FT232RQ). Both packages are lead ( Pb ) free, and use a `green' compound. Both packages are fully compliant with European Union directive 2002/95/EC.
Figure 1 - The UM232R Module.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
3. UM232R Pin Out and Signal Descriptions
3.1 UM232R Pin Out
UM232R (c) FTDI 2005
Page 6
TXD 1 DTR# RTS# VIO RXD RI# GND DSR# DCD# CTS# CB4 CB2 12
1 J1
2
3
24 GND
Jumper J1
2 J2
1
CB0 CB1 VCC RST 3V3 CB3 PU1 PU2 VCC USB 13 SLD
Figure 2 - Module Pin Out and Jumper locations.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
FT232RL
FTDI
Jumper J2
(c) Future Technology Devices International Ltd. 2005
3.2 Signal Descriptions
Table 1 - Module Pin Out Description Pin No. Name
1 2 3 4 TXD DTR# RTS# VIO
Page 7
Type
Output Output Output PWR
Description
Transmit Asynchronous Data Output.* Data Terminal Ready Control Output / Handshake signal.* Request To Send Control Output / Handshake signal.* +1.8V to +5.25V supply to the UART Interface and CBUS I/O pins (1...3, 5, 6, 9...14, 22, 23). In USB bus powered designs connect to 3V3 to drive out at 3.3V levels (connect jumper J1 pins 1 and 2 together), or connect to VCC to drive out at 5V CMOS level (connect jumper J1 pins 2 and 3 together). This pin can also be supplied with an external 1.8V - 2.8V supply in order to drive out at lower levels. It should be noted that in this case this supply should originate from the same source as the supply to Vcc. This means that in bus powered designs a regulator which is supplied by the 5V on the USB bus should be used. Receive Asynchronous Data Input.* Ring Indicator Control Input. When remote wake up is enabled in the internal EEPROM taking RI# low can be used to resume the PC USB host controller from suspend.* Module ground supply pins Data Set Ready Control Input / Handshake signal.* Data Carrier Detect Control input.* Clear to Send Control input / Handshake signal.* Configurable CBUS I/O Pin. Function of this pin is configured in the device internal EEPROM. Factory Default pin function is SLEEP#. See CBUS Signal Options, Table 4.* Configurable CBUS I/O Pin. Function of this pin is configured in the device internal EEPROM. Factory Default pin function is TXDEN. See CBUS Signal Options, Table 4.* USB Cable shield. 5V Power output USB port. For a low power USB bus powered design, up to 100mA can be sourced from the 5V supply on the USB bus. A maximum of 500mA can be sourced from the USB bus in a high power USB bus powered design. These two pins are internally connected on the module pcb. To power the module from the 5V supply on USB bus connect jumper J2 pins 1 and 2 together (this is the module default configuration). In this case these pins would have the same description as pin 14. To use the UM232R module in a self powered configuration ensure that jumper J2 pins 1 and 2 are not connected together, and apply an external 3.3V to 5.25V supply to one of these pins. Pull up resistor pin connection 2. Conect to pin 17 (RST#) in a self powered configuration. Pull up resistor pin connection 1. Connect to pin 14 (USB) in a self powered configuration 3.3V output from integrated L.D.O. regulator. This pin is decoupled to ground on the module pcb with a 10nF capacitor. The prime purpose of this pin is to provide the internal 3.3V supply to the USB transceiver cell and the internal 1.5k pull up resistor on USBDP. Up to 50mA can be drawn from this pin to power external logic if required. This pin can also be used to supply the FT232RL's VCCIO pin by connecting this pin to pin 4 (VIO), or by connecting together pins 1 and 2 on jumper J1. Can be used by an external device to reset the FT232R. If not required can be left unconnected, or pulled up to VCCIO. Configurable CBUS I/O Pin. Function of this pin is configured in the device internal EEPROM. Factory Default pin function is PWREN#. See CBUS Signal Options, Table 4.* Configurable CBUS I/O Pin. Function of this pin is configured in the device internal EEPROM. Factory Default pin function is RXLED#. See CBUS Signal Options, Table 4.* Configurable CBUS I/O Pin. Function of this pin is configured in the device internal EEPROM. Factory Default pin function is TXLED#. See CBUS Signal Options, Table 4.*
5 6 7, 24 8 9 10 11 12 13 14
RXD RI# GND DSR# DCD# CTS# CB4 CB2 SLD USB
Input Input PWR Input Input Input I/O I/O GND Output
15, 21
VCC
PWR or Output
16 17 19
PU2 PU1 3V3
Control Control Output
20 18 22 23
RST# CB3 CB1 CB0
Input I/O I/O I/O
* When used in Input Mode, these pins are pulled to VCCIO via internal 200k resistors. These pins can be programmed to gently pull low during USB suspend ( PWREN# = "1" ) by setting an option in the internal EEPROM.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
3.3 Jumper Configuration Options
Table 2 - Jumper J1 Pin Description Pin No. Name
1 3V3
Page 8
Type
Output
Description
3.3V output from integrated L.D.O. regulator. This pin is decoupled to ground on the module pcb with a 10nF capacitor. The prime purpose of this pin is to provide the internal 3.3V supply to the USB transceiver cell and the internal 1.5k pull up resistor on USBDP. Up to 50mA can be drawn from this pin to power external logic if required. This pin can also be used to supply the FT232RL's VCCIO pin by connecting this pin to pin 4 (VIO), or by connecting together pins 1 and 2 on jumper J1. +1.8V to +5.25V supply to the UART Interface and CBUS I/O pins (1...3, 5, 6, 9...14, 22, 23). In USB bus powered designs connect to 3V3 to drive out at 3.3V levels (connect jumper J1 pins 1 and 2 together), or connect to VCC to drive out at 5V CMOS level (connect jumper J1 pins 2 and 3 together). This pin can also be supplied with an external 1.8V - 2.8V supply in order to drive out at lower levels. It should be noted that in this case this supply should originate from the same source as the supply to Vcc. This means that in bus powered designs a regulator which is supplied by the 5V on the USB bus should be used. VCC Output. This will be 5V from the USB bus if pins 1 and 2 on jumper J2 are connected. Alternativly, if the module is in a self powered configuration, the supply to the VCC module pins (15 and 21) will be brought out to this jumper pin. Connect this jumper J1 pin 2 in order to supply the device IO pins from the supply to VCCIO.
2
VIO
PWR
3
VCC
PWR
Table 3 - Jumper J2 Pin Description Pin No. Name
1 USB
Type
PWR
Description
5V Power output USB port. For a low power USB bus powered design, up to 100mA can be sourced from the 5V supply on the USB bus. A maximum of 500mA can be sourced from the USB bus in a high power USB bus powered design. Board supply input. Connect to jumper J2 pin 1 in order to supply the board from the USB bus. This pin is internally connected to the VCC DIP pins. Remove the jumper connector in a self powered design.
2
VCC
PWR or Output
3.4 CBUS Signal Options
The following options can be configured on the CBUS I/O pins. These options are all configured in the internal EEPROM using the utility software MPROG, which can be downloaded from the FTDI website. The default configuration is described in Section 8. Table 4 - CBUS Signal Options CBUS Signal Option Available On CBUS Pin...
TXDEN PWREN# CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4
Description
Enable transmit data for RS485 Goes low after the device is configured by USB, then high during USB suspend. Can be used to control power to external logic PChannel logic level MOSFET switch. Enable the interface pull-down option when using the PWREN# pin in this way. Transmit data LED drive - pulses low when transmitting data via USB. See FT232R datasheet for more details. Receive data LED drive - pulses low when receiving data via USB. See FT232R datasheet for more details. LED drive - pulses low when transmitting or receiving data via USB. See FT232R datasheet for more details. Goes low during USB suspend mode. Typically used to power down an external TTL to RS232 level converter I.C. in USB to RS232 converter designs. 48MHz Clock output. 24MHz Clock output. 12MHz Clock output. 6MHz Clock output. CBUS bit bang mode option. Allows up to 4 of the CBUS pins to be used as general purpose I/O. Configured individually for CBUS0, CBUS1, CBUS2 and CBUS3 in the internal EEPROM. A separate application note will describe in more detail how to use CBUS bit bang mode. Synchronous and asynchronous bit bang mode WR# strobe Output Synchronous and asynchronous bit bang mode RD# strobe Output (c) Future Technology Devices International Ltd. 2005
TXLED# RXLED# TX&RXLED# SLEEP#
CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4
CLK48 CLK24 CLK12 CLK6 CBitBangI/O
CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3, CBUS4 CBUS0, CBUS1, CBUS2, CBUS3
BitBangWRn BitBangRDn
CBUS0, CBUS1, CBUS2, CBUS3 CBUS0, CBUS1, CBUS2, CBUS3
UM232R USB-Serial UART Development Module Datasheet Version 1.02
4. Module Dimensions
Figure 3 - UM232R Module Dimensions
Page 9
I
7.50mm (0.30")
5.50mm (0.22")
21.30mm (0.85")
33.00mm (1.50")
10.50mm (0.42")
5.80mm (0.23")
5.0mm (0.2")
12.50mm (0.50")
15.00mm (0.60")
All dimensions are in millimeters, with inches in parenthesis. The FT232RL is supplied in a RoHS compliant 28 pin SSOP package. The package is lead ( Pb ) free and uses a `green' compound. The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. The UM232R module uses exclusivly lead free components. Both the I.C. device and the module are fully compliant with European Union directive 2002/95/EC.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
FT D
2.54mm (0.10")
Diameter 0.50mm (0.02")
15.00mm (0.60")
12.00mm (0.48")
2.54mm (0.10")
18.10mm (0.72")
1.60mm (0.06")
(c) Future Technology Devices International Ltd. 2005
5. FT232RL Device Characteristics and Ratings
5.1 Absolute Maximum Ratings
Page 10
The absolute maximum ratings for the FT232R devices are as follows. These are in accordance with the Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the device. Table 5 - Absolute Maximum Ratings Parameter
Storage Temperature Floor Life (Out of Bag) At Factory Ambient ( 30C / 60% Relative Humidity) Ambient Temperature (Power Applied) Vcc Supply Voltage D.C. Input Voltage - USBDP and USBDM D.C. Input Voltage - High Impedance Bidirectionals D.C. Input Voltage - All other Inputs D.C. Output Current - Outputs DC Output Current - Low Impedance Bidirectionals Power Dissipation (Vcc = 5.25V)
Value
-65C to 150C 168 Hours (IPC/JEDEC J-STD-033A MSL Level 3 Compliant)* -40C to 85C -0.5 to +6.00 -0.5 to +3.8 -0.5 to +(Vcc +0.5) -0.5 to +(Vcc +0.5) 24 24 500
Unit
Degrees C Hours
Degrees C. V V V V mA mA mW
* If devices are stored out of the packaging beyond this time limit the devices should be baked before use. The devices should be ramped up to a temperature of 125C and baked for up to 17 hours.
5.2 DC Characteristics
DC Characteristics ( Ambient Temperature = -40 to 85oC ) Table 6 - Operating Voltage and Current Parameter
Vcc1 Vcc2 Icc1 Icc2
Description
VCC Operating Supply Voltage VCCIO Operating Supply Voltage Operating Supply Current Operating Supply Current
Min
3.3 1.8 50
Typ
15 70
Max
5.25 5.25 100
Units
V V mA
Conditions
Normal Operation USB Suspend*
A
Table 7 - UART and CBUS I/O Pin Characteristics (VCCIO = 5.0V, Standard Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
3.2 0.3 1.3 50
Typ
4.1 0.4 1.6 55
Max
4.9 0.6 1.9 60
Units
V V V mV
Conditions
I source = 2mA I sink = 2mA ** **
Table 8 - UART and CBUS I/O Pin Characteristics (VCCIO = 3.3V, Standard Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
2.2 0.3 1.0 20
Typ
2.7 0.4 1.2 25
Max
3.2 0.5 1.5 30
Units
V V V mV
Conditions
I source = 1mA I sink = 2mA ** **
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
Page 11
Table 9 - UART and CBUS I/O Pin Characteristics (VCCIO = 2.8V, Standard Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
2.1 0.3 1.0 20
Typ
2.6 0.4 1.2 25
Max
3.1 0.5 1.5 30
Units
V V V mV
Conditions
I source = 1mA I sink = 2mA ** **
Table 10 - UART and CBUS I/O Pin Characteristics (VCCIO = 5.0V, High Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
3.2 0.3 1.3 50
Typ
4.1 0.4 1.6 55
Max
4.9 0.6 1.9 60
Units
V V V mV
Conditions
I source = 6mA I sink = 6mA ** **
Table 11 - UART and CBUS I/O Pin Characteristics (VCCIO = 3.3V, High Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
2.2 0.3 1.0 20
Typ
2.8 0.4 1.2 25
Max
3.2 0.6 1.5 30
Units
V V V mV
Conditions
I source = 3mA I sink = 8mA ** **
Table 12 - UART and CBUS I/O Pin Characteristics (VCCIO = 2.8V, High Drive Level) Parameter
Voh Vol Vin VHys
Description
Output Voltage High Output Voltage Low Input Switching Threshold Input Switching Hysteresis
Min
2.1 0.3 1.0 20
Typ
2.8 0.4 1.2 25
Max
3.2 0.6 1.5 30
Units
V V V mV
Conditions
I source = 3mA I sink = 8mA ** **
**Inputs have an internal 200k pull-up resistor to VCCIO. Table 13 - RESET# and TEST Pin Characteristics Parameter
Vin VHys
Description
Input Switching Threshold Input Switching Hysteresis
Min
1.3 50
Typ
1.6 55
Max
1.9 60
Units
V mV
Conditions
Table 14 - USB I/O Pin (USBDP, USBDM) Characteristics Parameter
UVoh UVol UVse UCom UVDif UDrvZ
Description
I/O Pins Static Output ( High) I/O Pins Static Output ( Low ) Single Ended Rx Threshold Differential Common Mode Differential Input Sensitivity Driver Output Impedance
Min
2.8 0 0.8 0.8 0.2 26
Typ
Max
3.6 0.3 2.0 2.5
Units
V V V V V
Conditions
RI = 1.5k to 3V3Out ( D+ ) RI = 15k to GND ( D- ) RI = 1.5k to 3V3Out ( D+ ) RI = 15k to GND ( D- )
29
44
Ohms
***
***Driver Output Impedance includes the internal USB series resistors on USBDP and USBDM pins.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
Page 12
5.3 EEPROM Reliability Characteristics
The internal 1024 bit EEPROM has the following reliability characteristicsTable 15 - EEPROM Characteristics Parameter Description
Data Retention Read / Write Cycles
Value
15 100,000
Unit
Years Cycles
5.4 Internal Clock Characteristics
The internal Clock Oscillator has the following characteristics. Table 16 - Internal Clock Characteristics Parameter Min
Frequency of Operation Clock Period Duty Cycle 11.98 83.19 45
Value Typical
12.00 83.33 50
Unit Max
12.02 83.47 55 MHz ns %
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
6. Module Configurations
6.1 Bus Powered Configuration
Page 13
1
J1
24
FTDI
J2
12 13
Figure 4 - Bus Powered Configuration Figure 4 illustrates the UM232R module in a typical USB bus powered design configuration. This can easily be done by fitting the jumper link on J2, as shown above. The UM232R is supplied in this configuration by default. A USB Bus Powered device gets its power from the USB bus. Basic rules for USB Bus power devices are as follows - i) ii) On plug-in to USB, the device must draw no more than 100mA. On USB Suspend the device must draw no more than 500A.
iii) A Bus Powered High Power USB Device (one that draws more than 100mA) should use one of the CBUS pins configured as PWREN# and use it to keep the current below 100mA on plug-in and 500A on USB suspend. iv) A device that consumes more than 100mA can not be plugged into a USB Bus Powered Hub. v) No device can draw more that 500mA from the USB Bus. Interfacing the UM232R module to a microcontroller (MCU), or other logic for a bus powered design would be done in exactly the same way as for a self powered design (see Section 6.2), except that the MCU or external logic would take its power supply from the USB bus (either the 5V on the USB pin, or 3.3V on the 3V3 pin).
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
6.2 Self Powered Configuration
Vcc = 3.3V - 5V
Page 14
Vcc = 3.3V - 5V
TXD 1
TXD RXD RTS# 3
J1
24 GND
RTS# MCU CTS#
21 VCC
RXD 5
20 RST#
FTDI
GND 7
17 PU1 16 PU2
CTS# 10
15 VCC
J2
12
14 USB
13
Figure 5 - Self Powered Configuration Figure 5 illustrates the UM232R in a typical USB self powered configuration. In this case the link on jumper J2 is removed, and an external supply is connected to the module VCC pins. Figure 5 illustrates a self powered design which has a 3.3V - 5V supply. A USB Self Powered device gets its power from its own power supply and does not draw current from the USB bus. The basic rules for USB Self powered devices are as follows - i) ii) A Self Powered device should not force current down the USB bus when the USB Host or Hub Controller is powered down. A Self Powered Device can use as much current as it likes during normal operation and USB suspend as it has its own power supply.
iii) A Self Powered Device can be used with any USB Host and both Bus and Self Powered USB Hubs. In this case the power descriptor in the internal EEPROM should be programmed to a value of zero (self powered). In order to meet requirement (i) the USB Bus Power is used to control the RESET# Pin of the FT232R device. When the USB Host or Hub is powered up the internal 1.5k resistor on USBDP is pulled up to 3.3V, thus identifying the device as a full speed device to USB. When the USB Host or Hub power is off, RESET# will go low and the device will be held in reset. As RESET# is low, the internal 1.5k resistor will not be pulled up to 3.3V, so no current will be forced down USBDP via the 1.5k pull-up resistor when the host or hub is powered down. To do this pin 14 (USB) is connected to PU2 and PU1 is connected to RST#. Failure to do this may cause some USB host or hub controllers to power up erratically. Note : When the FT232R is in reset, the UART interface pins all go tri-state. These pins have internal 200k pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic. Figure 5 is also an example of interfacing the FT232R to a Microcontroller (MCU) UART interface. This example uses TXD and RXD for transmission and reception of data, and RTS# / CTS# hardware handshaking. Optionally, RI# can be connected to another I/O pin on the MCU and could be used to wake up the USB host controller from suspend mode. One of the CBUS pins could be configured as a 6/12/24/48 MHz clock output which can be used to clock the MCU. If the MCU is handling power management functions, then a CBUS pin can be configured as PWREN# and should also be connected to an I/O pin of the MCU.
UM232R USB-Serial UART Development Module Datasheet Version 1.02 (c) Future Technology Devices International Ltd. 2005
6.3 USB Bus Powered with Power Switching Configuration
Switched 5V Power to External Logic
Page 15
P-Channel Power MOSFET
s d
0.1 uF 0.1 uF
TXD 1
g
TXD RXD RTS# 3 RXD 5
J1
24
Soft 1k Start Circuit
RTS# MCU CTS#
FTDI
GND 7
18 CB3 (PWREN#)
CTS# 10
J2
12
14 USB
13
Figure 6 - Bus Powered with Power Switching Configuration USB Bus powered circuits need to be able to power down in USB suspend mode in order to meet the <= 500A total USB suspend current requirement (including external logic). Some external logic can power itself down into a low current state by monitoring the PWREN# signal. For external logic that cannot power itself down in this way, the FT232R provides a simple but effective way of turning off power to external circuitry during USB suspend. Figure 6 shows how to use a discrete P-Channel Logic Level MOSFET to control the power to external logic circuits. A suitable device would be an International Rectifier (www.irf.com) IRLML6402, or equivalent. It is recommended that a "soft start" circuit consisting of a 1k series resistor and a 0.1F capacitor are used to limit the current surge when the MOSFET turns on. Without the soft start circuit there is a danger that the transient power surge of the MOSFET turning on will reset the FT232R, or the USB host / hub controller. The values used here allow attached circuitry to power up with a slew rate of ~12.5V per millisecond, in other words the output voltage will transition from GND to 5V in approximately 400 microseconds. Alternatively, a dedicated power switch I.C. with inbuilt "soft-start" can be used instead of a MOSFET. A suitable power switch I.C. for such an application would be a Micrel (www.micrel.com) MIC2025-2BM or equivalent. Please note the following points in connection with power controlled designs - i) ii) The logic to be controlled must have its own reset circuitry so that it will automatically reset itself when power is reapplied on coming out of suspend. Set the Pull-down on Suspend option in the internal EEPROM.
iii) One of the CBUS Pins should be configured as PWE# in the internal EEPROM, and should be used to switch the power supply to the external circuitry. iv) For USB high-power bus powered device (one that consumes greater than 100mA, and up to 500mA of current from the USB bus), the power consumption of the device should be set in the max power field in the internal EEPROM. A high-power bus powered device must use this descriptor in the internal EEPROM to inform the system of its power requirements. v) For 3.3V power controlled circuits the FT232R's VCCIO pin must not be powered down with the external circuitry (the PWREN# signal gets its VCC supply from VCCIO). Either connect the power switch between the output of the 3.3V regulator and the external 3.3V logic or power VCCIO from the 3V3OUT pin of the FT232R.
UM232R USB-Serial UART Development Module Datasheet Version 1.02 (c) Future Technology Devices International Ltd. 2005
6.4 USB Bus Powered with 3.3V Logic Drive / IO Supply Voltage
Page 16
1
J1
1
2
3
24
FTDI
J2
12 13
Figure 7 - USB Bus Powered 3.3V Logic Drive Figure 7 shows a configuration where a jumper switch is used to allow the FT232R to be interfaced with a 3.3V or 5V logic devices. The FT232R's VCCIO pin is either supplied with 5V from the USB bus (connect together pins 2 and 3 on J1), or with 3.3V from the FT232R's 3V3OUT pin (connect together pins 1 and 2 on J1 as shown). The supply to UM232R's 3V3 pin can also be used to supply up to 50mA to external logic. Please note the following in relation to bus powered designs of this type i) ii) PWREN# or SLEEP# signals should be used to power down external logic during USB suspend mode, in order to comply with the limit of 500A. If this is not possible, use the configuration shown in Section 6.3. The maximum current source from USB Bus during normal operation should not exceed 100mA, otherwise a bus powered design with power switching (Section 6.3) should be used.
Another possible configuration would be to use a discrete low dropout regulator which is supplied by the 5V on the USB bus to supply 2.8V - 1.8V to the VIO pin and to the external logic. VCC would be supplied with the 5V from the USB bus (available from the module's USB pin). With VIO connected to the output of the low dropout regulator, would in turn will cause the FT232R I/O pins to drive out at 2.8V - 1.8V logic levels. For USB bus powered circuits some considerations have to be taken into account when selecting the regulator - iii) The regulator must be capable of sustaining its output voltage with an input voltage of 4.35V. A Low Drop Out (L.D.O.) regulator must be selected. iv) The quiescent current of the regulator must be low in order to meet the USB suspend total current requirement of <= 500A during USB suspend. An example of a regulator family that meets these requirements is the MicroChip / Telcom TC55 Series of devices (www.microchip.com). These devices can supply up to 250mA current and have a quiescent current of under 1A.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
J2 2 VCC
U1
Ferrite Bead
FB1
1
CN1
10nF +
VCC
1
USB
C1
TXD 1
20 VCC
TXD
PL1
TXD
1
X
X
24
GND
2 3 4
5
C3
RXD 5 RTS# 3
RXD RTS#
DTR#
2
16 USBDM 15 USBDP
VIO
C2
X
X
23
CB0
RTS#
3
X
X
22
CB1
47pF +
47pF +
4 VCCIO
8 NC
RST#
FT232R
19 RESET# 24 NC
27 OSCI
CTS# 11 DTR# 2 DSR# 9 DCD# 10
28 OSCO
CTS# DTR# DSR# DCD#
VIO
4
X
X
21
VCC
RXD
5
X
X
20
RST#
RI#
6
SLD
X
X
19
3V3
7. UM232R Module Circuit Schematic
PU2
GND
3V3
10k
RI# 6
RI#
X
X
DSR#
8
R2
17 3V3OUT
3V3
VCC
VIO VCC
J1 1 2 3
CBUS0 23 CBUS1 22
C4
CB0 CB1
X
X
17
PU1
DCD#
9
X
X
16
PU2
PU1
CTS# 10
0.1uF
10k
4.7uF + C6
0.1uF
GND
X
X
15
VCC
R1
C5
Figure 8 - Module Circuit Schematic
A G N D 25
GND
G N D 7
G N D 18
G N D 21
T E S T 26
CBUS2 13 CBUS3 14
CBUS4 12
CB2 CB3 CB4
CB4
11
X
X
14
USB
CB2
12
X
X
13
SLD
GND
SKT24
GND
UM232R USB-Serial UART Development Module Datasheet Version 1.02
GND
7
18
CB3
(c) Future Technology Devices International Ltd. 2005
Page 17
8. Internal EEPROM Configuration
Page 18
Following a power-on reset or a USB reset the FT232R will scan its internal EEPROM and read the USB configuration descriptors stored there. The default values programmed into the internal EEPROM in the FT232RL used on the UM232R are shown in Table 17. Table 17 - Default Internal EEPROM Configuration Parameter
USB Vendor ID (VID) USB Product ID (PID) Serial Number Enabled? Serial Number Pull Down I/O Pins in USB Suspend Manufacturer Name Manufacturer ID Product Description Max Bus Power Current Power Source Device Type USB Version
Value
0403h 6001h Yes See Note Disabled FTDI FT UM232R USB <-> Serial 100mA Bus Powered FT232R 0200
Notes
FTDI default VID (hex) FTDI default PID (hex)
A unique serial number is generated and programmed into the EEPROM during final test of the UM232R module. Enabling this option will make the device pull down on the UART interface lines when the power is shut off (PWREN# is high) Serial Number prefix.
Returns USB 2.0 device descriptor to the host. Note: The device is be a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). Taking RI# low will wake up the USB host controller from suspend. Enables the high drive level on the UART and CBUS I/O pins Makes the device load the VCP driver interface for the device. Default configuration of CBUS0 - Transmit LED drive Default configuration of CBUS1 - Receive LED drive Default configuration of CBUS2 - Power enable. Low after USB enumeration, high during USB suspend. Default configuration of CBUS3 - Power enable. Low after USB enumeration, high during USB suspend. Default configuration of CBUS4 - Low during USB suspend. Signal on this pin becomes TXD# if enabled. Signal on this pin becomes RXD# if enabled. Signal on this pin becomes RTS if enabled. Signal on this pin becomes CTS if enabled. Signal on this pin becomes DTR if enabled. Signal on this pin becomes DSR if enabled. Signal on this pin becomes DCD if enabled. Signal on this pin becomes RI if enabled.
Remote Wake up High Current I/Os Load VCP Driver CBUS0 CBUS1 CBUS2 CBUS3 CBUS4 Invert TXD Invert RXD Invert RTS# Invert CTS# Invert DTR# Invert DSR# Invert DCD# Invert RI#
Enabled Disabled Enabled TXLED# RXLED# PWREN# PWREN# SLEEP# Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled
The internal EEPROM in the FT232R can be programmed over USB using the utility program MPROG. MPROG can be downloaded from the FTDI website. Version 2.8a or later is required for the FT232R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service.
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005
Disclaimer
Copyright (c) Future Technology Devices International Limited , 2005.
Version 0.9 - Initial Datasheet Created August 2005 Version 1.00 - Full datasheet release December 2005 Version 1.01 - Circuit schematic diagram updated January 2006 Version 1.02 - Module PCB length dimensions January 2006
Page 19
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd. will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice.
Contact FTDI
Head Office Future Technology Devices International Ltd. 373 Scotland Street, Glasgow G5 8QB, United Kingdom Tel. : +(44) 141 429 2777 Fax. : +(44) 141 429 2758 E-Mail (Sales) : sales1@ftdichip.com E-Mail (Support) : support1@ftdichip.com E-Mail (General Enquiries) : admin1@ftdichip.com Regional Sales Offices Future Technology Devices International Ltd. (Taiwan) 4F, No 16-1, Sec. 6 Mincyuan East Road, Neihu District, Taipei 114, Taiwan, R.o.C. Tel.: +886 2 8791 3570 Fax: +886 2 8791 3576 E-Mail (Sales): tw.sales@ftdichip.com E-Mail (Support): tw.support@ftdichip.com E-Mail (General Enquiries): tw.admin@ftdichip.com Website URL : http://www.ftdichip.com Future Technology Devices International Ltd. (USA) 5285 NE Elam Young Parkway, Suite B800 Hillsboro, OR 97124-6499 USA Tel.: +1 (503) 547-0988 Fax: +1 (503) 547-0987 E-Mail (Sales): us.sales@ftdichip.com E-Mail (Support): us.support@ftdichip.com E-Mail (General Enquiries): us.admin@ftdichip.com
UM232R USB-Serial UART Development Module Datasheet Version 1.02
(c) Future Technology Devices International Ltd. 2005

▲Up To Search▲

Price & Availability of UM232R

	To Download UM232R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .